Coin laundry, also known as laundromat, is laundry facility wherein people pay to use washing machines and dryers to wash or launder their clothes. Here you go Reddit, Free Coin Op. According to reports, this coin operated washer and dryer manufactured by Encore has a load capacity of 3.5 cubic feet.

As a laundromat owner you know there is nothing more frustrating than having a coin jammed in one of your machines. Whether the cause of the jam is a damaged coin or a worn out slide mechanism, remedying the problem can be easy if you know how to take the machine apart to get to the stuck coin. If you need a new or used vended dryer or vended commercial washer in Charleston, SC, make the call to T & L Laundry Equipment for big savings.

Ideally, a stuck coin should dislodge from the chute with a press of the coin return button. However, when that doesn't do the trick, there are a few tried and true things you can try to get that coin to move before you take the assembly apart.

• Put another coin into the slot and attempt to use this action to dislodge the stuck coin.
• Slap the side of the machine where the coin slot is located to get the coin to move.
• Place a piece of wood or something to protect the finish of the machine and tap on the wood with a hammer to unjam the coin. Use caution not to hammer so hard that you cause damage to the machine. A gentle vibration may loosen the coin.
• If the coin has tipped inside the coin slot, the coin slot may not move. Using a utility knife to push the coin upright may allow it to pass through normally.
• Attempt to pull the coin out of the slot with tweezers.

If the coin slide, rather than the coin, is the issue you may need to disassemble the coin acceptor. Follow these steps to correct the issue:

• Remove the coin store tray and empty it. Check to see if anything is blocking the coin shoot inside.
• Take off the maintenance panel on the top face of the coin slide housing. The panel is usually locked in the back with a key.
• Remove the long bolt that runs from the maintenance panel to the front of the housing.
• Disconnect any wiring from the slot mechanism and carefully free the mechanism from the housing.

Washing Machine Repair Near Me

The offending coin or debris should be able to be clearly seen at this point. Once you have cleared the slot, test the mechanism with a fresh coin before you reassemble the mechanism.

It is important to note the placement of any nuts, screws, connections, or other parts as you disassemble the coin slide. If the problem continues, the mechanism may need to be replaced. The good news is that since you know how to remove it, you can replace it.

Affordable Commercial Washer in Charleston, SC

If you feel uncertain about taking this mechanism apart or need genuine manufacturer's replacement parts, give T & L Laundry Equipment a call. For more than 40 years we have provided vended and commercial laundry owners with exceptional service and support. Let our expert staff help you get the right vended dryer or commercial washer in Charleston, SC.

We proudly offer full product lines from some of the top manufacturers in the industry like Speed Queen and Continental. Known for their reliability and durability, these manufacturers lead the industry in technology and innovations that bring exciting innovations for owners and customers.

Ready to learn more about how T & Laundry Equipment can help you improve your business through the latest equipment, planned maintenance agreements and timely service? Make an appointment with a member of our sales team today and put our 40 years of industry experience to work for you!

Image Rights: www.chiefappliance.com

Today I was called out to one of my machines in which the coin slide mechanism had been jammed. The machine was a Speed Queen SWT111NW 3050 Washer. I thought this would be a good opportunity to take a couple photos with my trusty Iphone and put together this little service helper. Most owners of coin operated machines will quickly come across this situation. There are a lot of coins in circulation that are slightly bent or dented. Some damage is hardly noticeable so you can not blame the machine users ALL the time. Most of the manufacturers including Speed Queen, Maytag, GE & Whirlpool in the past 10-15 years have been using these 7 slot vertical Greenwald coin slides mechanisms. Here in Australia they have been designed to accept 20c, $1.00 or $2.00 coins just by changing the insert in which the coin fits and a little piece of metal which fits in the roof of the slide. Some service repairers may not like me showing how this is done but the fact of the matter if you have just a slight bit of mechanical knowledge most owners will attempt to do this repair anyway. If you own machinery it is advantageous to have a little knowledge to do simple repairs or else you will go broke. Although you are not working on the actual wiring there is still 24o volts quite close, so always unplug the machine before removing any covers.

Once you open up the service door with the service door key you will see a brass coloured bracket protruding from the end of the coin slide. The shape of this can vary quite a bit depending on the brand and model of the washer or dryer. Usually on the end of this bracket (as in this case) there is another bracket. This is the bracket which comes in contact with the time lever or on the newer model a micro switch for the electronic. On the Maytag machines for 10 years at least they have been using a push rod with a electronic sensor on the end. In any case you don’t really need to worry about what the bracket is actually activating. We are only interested in the bracket directly screwed to the slide. The only spanner you need is a 5/16″ socket or in some Maytag machines a 1/4″ socket, remembering that all these machines are American so they are still Imperial sizes. A small extension and handle or ratchet are also helpful. So remove both brackets.

5/16' Sockey with Extension and Spanner

You will see the picture I have taken the spanner is fitted to the end of the bolt. Once you loosen this bolt a turn with the spanner you should be able to turn it with you fingers and remove it the rest of the way.

You will see how this bolt goes right up to the front the cavity and bolts the slide mechanism onto the front of the cavity. It is fitted in the middle, close to the roof. You should be able to feel the bolt with your fingers.

Once you have taken the bolt out you should be able to lift the slide up slightly then pull the unit out. It locks into a couple locking slots that you will see once you have removed it. Take note how it slots in so can refit it on reassembly.

Removing Slide Mechanism

How To Choose A Washing Machine

Once you have removed the slide mechanism it is usually quite an obvious job to remove the coin which has jammed it. When you are ready for reassembly I usually spray the assembly with a small amount of lubricant spray such as WD40.

Washing Machine How To Clean

Reassembly is the exact opposite of dismantling. The only trick sometime is getting that long bolt to make contact with the tread at the end of the cavity. It is a matter of holding your tongue in the right position or a couple of choice words. There is a hole in a bracket half way back which helps line up the thread at the end. Once you have done this job a couple times it does become easier.

How To Work A Washing Machine

Once you have reassembled the slide put a set of coins through the slide to ensure it is going to continue working.